Roborock Saros 10 with Refill & Drainage System

Suction in pascal, as the maker measures it. More pascal helps on carpet, but it says little about how well the robot picks grit off a hard floor.

A brush that guides hair to the side instead of letting it wind around the shaft. It saves the cutting work in homes with long hair or pets.

The side brush swings out in a corner or along a baseboard, so the dust there is swept in too.

The robot notices when it drives onto a carpet. Most then raise their suction, and a mopping robot lifts its mop or leaves it at the dock.

Whether the robot copes with pet hair: a brush that hair does not wind around and a dock that empties the bin for you. Where the maker does not say so itself, we read it from those two.

A sensor notices where more dirt lies, at the doormat for example, and the robot cleans that patch longer or a second time.

How the mop is built: flat pads, two spinning discs or a roller. Discs press harder on dried-on dirt, a roller rinses itself while it works.

The pad slides out along a wall or a baseboard, so the last few inches are mopped as well.

The robot leaves the mop at the dock before it vacuums a carpet, so the carpet never gets wet.

The dock empties the robot’s dust bin, usually after every run. You only empty the dock’s bag or bin.

The dock collects dust in a bin instead of a disposable bag. No bags to buy, but you empty it yourself.

The dock washes the mop for you, so you do not rinse it by hand.

How hot the dock washes the mop. Above 140 °F (60 °C) grease comes off, which is what keeps a mop from smelling.

The dock dries the mop afterwards, so it does not sit there wet and start to smell.

Drying is done with warm air instead of cold. It is faster and it helps against smell.

The dock mixes detergent into the water itself, from its own bottle.

The dock can be connected to the tap and the drain, so you never fill or empty a tank. It does need a connection nearby.

The width, depth and height of the dock. Measure the spot you have in mind, and leave room for the lid and for the robot driving in.

How the robot maps your home and follows that map. Lidar measures with a laser and works in the dark, a camera looks along and recognizes more.

How the robot sees loose things on the floor, such as cables, socks or a pet accident. A camera with depth sensing sees more than a bumper that reacts on contact.

The highest threshold the robot takes, as the maker states it. Measure your own: the step into a bathroom or onto a balcony is often higher.

Two steps close together, such as a threshold with a sliding-door track behind it: their combined height, as the maker measures it. Each brand measures with a different gap between the steps, so compare this figure across brands with care. For a single step, the threshold above applies.

An extending leg or wheel that carries the robot over a high threshold. Without one it usually stops at about 0.8 in (2 cm).

Whether the robot has a camera, and what for: to recognize obstacles, or also to show you a live picture of your home in the app.

How tall the robot is. It decides whether it fits under your sofa, bed or cabinet.

How wide the robot is. Narrower gets between chair legs more easily, wider usually means a bigger dust bin.

The noise in decibels, in the setting its source names: makers mostly give the standard setting, stores often the highest. 65 dB is like a vacuum at half power, 55 dB like a conversation.

The capacity of the battery. It hints at the runtime, but how much the robot draws counts just as much.

How long the robot cleans on one charge, at its quietest setting. After that it recharges and carries on where it stopped.

Matter is the standard that lets devices from different makers work together. With it you can run the robot outside the maker’s own app.

Which voice assistants the robot works with, such as Google Assistant or Alexa.

The warranty the maker gives in the United States.

Whether the robot works with Home Assistant, the home automation software you run yourself. Official means the integration comes with Home Assistant itself, community that volunteers maintain it.